CHROMATIZING Aluminium chromate and its applications What we call as phosphating to steel an iron is called chromating for aluminium surfaces. Also it is knows as alodine coating. There are yellow, green and transparent chromating types. Yellow chromate coats Cr+6, green chromate coats Cr+3. Coating weight can vary according to application time and coating type. Drying temperature must not pass over 65 º C for yellow chromate and 85 º C for green and transparent chromate coatings. It is importat to provide clean, grease free surface before chromate application. If hot degreasing bath is prepared, caustic bath and following nitric acid bath can be used for pickling. On the other hand, acidic degreasing baths have pickling ability with itselves. Chromating and paint adhesion will be much better on pickled and degreased aluminium surface.

VC AR306 INTRODUCTION : VC AR306 is a powder based activator which is used at low concentrations prior to zinc phosphating. By dipping the parts in VC AR306 bath prior to phosphating, it accelerates the subsequent phosphating process and also refines the structure of the zinc phosphate coating resulting in smooth fine uniform compact coating. PROPERTIES : Colour : White Form : Free flowing powder PH of 0.2-0.3% : 8-9 APPLICATION : VC AR306 bath can be prepared in M.S. or plastic tank/container. It is to be used at 0.2% to 0.3% concentration with water, at room temperature for one minute. The bath should always be kept in a slightly agitated condition by mechanical means or by passing compressed air from the bottom of the tank to avoid settling of the activator at the bottom of the tank. MAINTENANCE OF BATH : Once the bath is prepared, daily addition should be made once during the day. Addition should be made when pH falls below 8. Always maintain pH between 8-9. New bath should be prepared once in week or once in 15 days, depending on the work load. PRECAUTION : 1. Since the product is alkaline in nature always wear PVC/Rubber gloves while handling or working with this product. 2. Any splashes on skin or eyes should be flushed off with plenty of water and thereafter immediately consult physician. 3. Use of eye goggles and apron is recommended. PACKING : 15 Kgs & 50 Kgs.

VCCLEAN-HD18 is an universal cleaning composition which could be used be very safely on any metal or assemblies. It can be used for general cleaning for removal of oils, soils, fabricating fluids, burrs, buffing and drawing compounds etc. It is extremely safe to handle and contains no toxic or hazardous constituents and is neither inflammable nor poisonous. It is a solvent based neutral cleaner which can be readily mixed with water in all proportions. VCCLEAN-HD18 can be used by wipe, or immersion in various types of equipments such as ultrasonics, tumblers, agitated tanks. No rinse is mandatory after cleaning with VCCLEAN-HD18 and hence it cleans and protects simultaneously. It can be used as a spray cleaner in service stations and maintenance depots at very low concentrations very effectively, but should not be used in spray washing machines. This composition is bio-degradable and environment friendly.

We deal in Room Temperature blackening Chemical, which customer can directly avail from us. GENERAL DESCRIPTION VCBLK HB-18 is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature.VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energysaving, fast, dependable and convenient. It increases productivity and lowers labour costs.Finishing can be done anywhere without special equipment, ventilation, heating systems or anycomplicated control procedures.EQUIPMENT REQUIREDAcid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used withVCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks andracks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used fordegreasing, rinsing & sealant tanks.DIRECTIONS FOR USE1. Thoroughly clean and degrease the pieces to be blackened in KLN 18. The type and degree ofsurface soil will determine the length of time and the number of cleaning steps and cleaningtemperature (M.S. Tank).2. Rinse thoroughly in overflowing cold water (M.S. Tank).3. Surface rust, if present, should be removed following cleaning cycle using RLN 27 at aconcentration of 1:1 at room temperature (FRP Tank).4. Rinse thoroughly in overflowing cold water (M.S. Tank).5. Immerse the pieces in VCBLK HB-18 solution. VCBLK HB-18 solution is to be diluted with 6to 12 parts of water depending on alloy and surface, hardness. The immersion time necessary toproduce the desired depth of black, is usually one to three minutes. For most parts a dilution ofone part VCBLK HB-18 with 9 parts of water would give good results (FRP Tank).6. Rinse the pieces in overflowing cold water for 30 seconds (M.S. Tank). 7. Immerse the pieces in oil, a dewatering type rust preventive at room temperature for 3 minutesto seal the finish and impart corrosion resistance (M.S. Tank).The above parts can be sealed while wet or dry. If parts have to be dried prior to sealing, step 6should be followed with a hot water rinse and the parts to be sealed as soon as they are dry.A wide range of rust preventives are available with us. Consult us on what type of finish andprotection you require for your parts or components and we can suggest a suitable oil.

We deal in Room Temperature blackening Chemical, which customer can directly avail from us. GENERAL DESCRIPTION VCBLK HB-18 is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature.VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energysaving, fast, dependable and convenient. It increases productivity and lowers labour costs.Finishing can be done anywhere without special equipment, ventilation, heating systems or anycomplicated control procedures.EQUIPMENT REQUIREDAcid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used withVCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks andracks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used fordegreasing, rinsing & sealant tanks.DIRECTIONS FOR USE1. Thoroughly clean and degrease the pieces to be blackened in KLN 18. The type and degree ofsurface soil will determine the length of time and the number of cleaning steps and cleaningtemperature (M.S. Tank).2. Rinse thoroughly in overflowing cold water (M.S. Tank).3. Surface rust, if present, should be removed following cleaning cycle using RLN 27 at aconcentration of 1:1 at room temperature (FRP Tank).4. Rinse thoroughly in overflowing cold water (M.S. Tank).5. Immerse the pieces in VCBLK HB-18 solution. VCBLK HB-18 solution is to be diluted with 6to 12 parts of water depending on alloy and surface, hardness. The immersion time necessary toproduce the desired depth of black, is usually one to three minutes. For most parts a dilution ofone part VCBLK HB-18 with 9 parts of water would give good results (FRP Tank).6. Rinse the pieces in overflowing cold water for 30 seconds (M.S. Tank). 7. Immerse the pieces in oil, a dewatering type rust preventive at room temperature for 3 minutesto seal the finish and impart corrosion resistance (M.S. Tank).The above parts can be sealed while wet or dry. If parts have to be dried prior to sealing, step 6should be followed with a hot water rinse and the parts to be sealed as soon as they are dry.A wide range of rust preventives are available with us. Consult us on what type of finish andprotection you require for your parts or components and we can suggest a suitable oil.

COLD BLACKENING GENERAL DESCRIPTION VCBLK HB-18 is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature. VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energy saving, fast, dependable and convenient. It increases productivity and lowers labour costs. Finishing can be done anywhere without special equipment, ventilation, heating systems or any complicated control procedures. EQUIPMENT REQUIRED Acid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used with VCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks and racks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used for degreasing, rinsing & sealant tanks.

Vitarag Chemicals welcomes you. We are proud to introduce ourselves as the leading manufacturer, suppliers of metal pretreatment chemicals in India. Professional Paint Strippingis heavy duty industrial Powder coating remover used for removal of paint & powder coating from the metal surface. The chemical penetrates through the film and the film bubbles out. It is used to remove all types of liquid as well as powder paints, lacquers, enamels & polyurethanes from a metal surface. Professional Paint Stripping is used by immersion application at room temperature. The dipping time may range from 1 to 5 min depending on the surrounding temperature, nature, and thickness of the paint. It may also be applied by brush on the surface of the coating to be removed. Allow standing for 1 to 5 min, depending on the nature and thickness of the coating to be removed. Two or more brush may have to be applied for complete removal of stubborn paint. Remove by scraping, brushing or water jet application. While there are several reasons why you should go for our company: We formulate products based on the end users specific requirements through extensive R& D and validation procedures. We provide reliable and quality products timely as we maintain strict quality control procedures for our raw materials and finished goods. We offer comprehensive customer support post supply We supply products at most competitive prices. In line with clients diverse requirements, we are involved in providing an optimum quality range of Powder Coating /Paint Remover Chemical.

Vitarag Chemicals welcomes you. We are proud to introduce ourselves as the leading manufacturer, suppliers of metal pretreatment chemicals in India. PCR-01 Non-Toxic Paint Stripper is heavy duty removal of paint from the metal surface. The chemical penetrates through the film and the film bubbles out. It is used to remove all types of liquid as well as powder paints, lacquers, enamels & polyurethanes from a metal surface. PCR 01 Non-Toxic Paint Stripper is used by immersion application at room temperature. The dipping time may range from 1 to 5 min depending on the surrounding temperature, nature, and thickness of the paint. It may also be applied by brush on the surface of the coating to be removed. Allow standing for 1 to 5 min, depending on the nature and thickness of the coating to be removed. Two or more brush may have to be applied for complete removal of stubborn paint. Remove by scraping, brushing or water jet application. While there are several reasons why you should go for our company: We formulate products based on the end users specific requirements through extensive R& D and validation procedures. We provide reliable and quality products timely as we maintain strict quality control procedures for our raw materials and finished goods. We offer comprehensive customer support post supply We supply products at most competitive prices. In line with clients diverse requirements, we are involved in providing an optimum quality range of Powder Coating /Paint Remover Chemical. Reaction Time is only 50 seconds for Removing Paint Layer.

1. Vitarag Chemicals welcomes you. We are proud to introduce ourselves as the leading manufacturer, suppliers of metal pretreatment chemicals in India. 2. PCR 01 Industrial paint remover is heavy duty industrial Powder coating remover used for removal of paint & powder coating from the metal surface. The chemical penetrates through the film and the film bubbles out. It is used to remove all types of liquid as well as powder paints, lacquers, enamels & polyurethanes from a metal surface. 3. PCR 01 Industrial paint remover is used by immersion application at room temperature. The dipping time may range from 1 to 5 min depending on the surrounding temperature, nature, and thickness of the paint. It may also be applied by brush on the surface of the coating to be removed. Allow standing for 1 to 5 min, depending on the nature and thickness of the coating to be removed. Two or more brush may have to be applied for complete removal of stubborn paint. Remove by scraping, brushing or water jet application. 4. While there are several reasons why you should go for our company: We formulate products based on the end users specific requirements through extensive R& D and validation procedures. We provide reliable and quality products timely as we maintain strict quality control procedures for our raw materials and finished goods. We offer comprehensive customer support post supply We supply products at most competitive prices.In line with clients diverse requirements, we are involved in providing an optimum quality range of Powder Coating /Paint Remover Chemical. Reaction Time is only 50 seconds for Removing Powder Coating Layer. Paint Remover Manufacturers Paint Remover Wholesalers Paint Remover Distributors Paint Remover Manufacturers near me Best Paint Remover Manufacturers In India Best Paint Remover Manufacturers In Gujarat