INTRODUCTION: Degreasing Chemical used whenever parts contains heavy grease, oil & light rust. This chemical also removes certain part of carbon. Base : Alkaline Base Chemical. Solubility : Thoroughly soluble in water. Color : white Concentration : 5% (w/v) is suitable for Hot process & in case of cold 8% required. Point : Concentrated of 8% bath Solution gives 6 to 8 ml. Point. Bath Design : Tank is made up of 10mm thick. M.S. tank with F.R.P. Vinyl coat of F.R.P. Lining works will be the most suitable or sustainable design

We deal in Room Temperature blackening Chemical, which customer can directly avail from us. GENERAL DESCRIPTION VCBLK HB-18 is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature.VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energysaving, fast, dependable and convenient. It increases productivity and lowers labour costs.Finishing can be done anywhere without special equipment, ventilation, heating systems or anycomplicated control procedures.EQUIPMENT REQUIREDAcid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used withVCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks andracks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used fordegreasing, rinsing & sealant tanks.DIRECTIONS FOR USE1. Thoroughly clean and degrease the pieces to be blackened in KLN 18. The type and degree ofsurface soil will determine the length of time and the number of cleaning steps and cleaningtemperature (M.S. Tank).2. Rinse thoroughly in overflowing cold water (M.S. Tank).3. Surface rust, if present, should be removed following cleaning cycle using RLN 27 at aconcentration of 1:1 at room temperature (FRP Tank).4. Rinse thoroughly in overflowing cold water (M.S. Tank).5. Immerse the pieces in VCBLK HB-18 solution. VCBLK HB-18 solution is to be diluted with 6to 12 parts of water depending on alloy and surface, hardness. The immersion time necessary toproduce the desired depth of black, is usually one to three minutes. For most parts a dilution ofone part VCBLK HB-18 with 9 parts of water would give good results (FRP Tank).6. Rinse the pieces in overflowing cold water for 30 seconds (M.S. Tank). 7. Immerse the pieces in oil, a dewatering type rust preventive at room temperature for 3 minutesto seal the finish and impart corrosion resistance (M.S. Tank).The above parts can be sealed while wet or dry. If parts have to be dried prior to sealing, step 6should be followed with a hot water rinse and the parts to be sealed as soon as they are dry.A wide range of rust preventives are available with us. Consult us on what type of finish andprotection you require for your parts or components and we can suggest a suitable oil.

We deal in Room Temperature blackening Chemical, which customer can directly avail from us. GENERAL DESCRIPTION VCBLK HB-18 is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature.VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energysaving, fast, dependable and convenient. It increases productivity and lowers labour costs.Finishing can be done anywhere without special equipment, ventilation, heating systems or anycomplicated control procedures.EQUIPMENT REQUIREDAcid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used withVCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks andracks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used fordegreasing, rinsing & sealant tanks.DIRECTIONS FOR USE1. Thoroughly clean and degrease the pieces to be blackened in KLN 18. The type and degree ofsurface soil will determine the length of time and the number of cleaning steps and cleaningtemperature (M.S. Tank).2. Rinse thoroughly in overflowing cold water (M.S. Tank).3. Surface rust, if present, should be removed following cleaning cycle using RLN 27 at aconcentration of 1:1 at room temperature (FRP Tank).4. Rinse thoroughly in overflowing cold water (M.S. Tank).5. Immerse the pieces in VCBLK HB-18 solution. VCBLK HB-18 solution is to be diluted with 6to 12 parts of water depending on alloy and surface, hardness. The immersion time necessary toproduce the desired depth of black, is usually one to three minutes. For most parts a dilution ofone part VCBLK HB-18 with 9 parts of water would give good results (FRP Tank).6. Rinse the pieces in overflowing cold water for 30 seconds (M.S. Tank). 7. Immerse the pieces in oil, a dewatering type rust preventive at room temperature for 3 minutesto seal the finish and impart corrosion resistance (M.S. Tank).The above parts can be sealed while wet or dry. If parts have to be dried prior to sealing, step 6should be followed with a hot water rinse and the parts to be sealed as soon as they are dry.A wide range of rust preventives are available with us. Consult us on what type of finish andprotection you require for your parts or components and we can suggest a suitable oil.

COLD BLACKENING GENERAL DESCRIPTION VCBLK HB-18 is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature. VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energy saving, fast, dependable and convenient. It increases productivity and lowers labour costs. Finishing can be done anywhere without special equipment, ventilation, heating systems or any complicated control procedures. EQUIPMENT REQUIRED Acid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used with VCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks and racks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used for degreasing, rinsing & sealant tanks.

GENERAL DESCRIPTION. VCBLK HB-18 is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature.VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energysaving, fast, dependable and convenient. It increases productivity and lowers labour costs.Finishing can be done anywhere without special equipment, ventilation, heating systems or anycomplicated control procedures.EQUIPMENT REQUIREDAcid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used withVCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks andracks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used fordegreasing, rinsing & sealant tanks.DIRECTIONS FOR USE1. Thoroughly clean and degrease the pieces to be blackened in KLN 18. The type and degree ofsurface soil will determine the length of time and the number of cleaning steps and cleaningtemperature (M.S. Tank).2. Rinse thoroughly in overflowing cold water (M.S. Tank).3. Surface rust, if present, should be removed following cleaning cycle using RLN 27 at aconcentration of 1:1 at room temperature (FRP Tank).4. Rinse thoroughly in overflowing cold water (M.S. Tank).5. Immerse the pieces in VCBLK HB-18 solution. VCBLK HB-18 solution is to be diluted with 6to 12 parts of water depending on alloy and surface, hardness. The immersion time necessary toproduce the desired depth of black, is usually one to three minutes. For most parts a dilution ofone part VCBLK HB-18 with 9 parts of water would give good results (FRP Tank).6. Rinse the pieces in overflowing cold water for 30 seconds (M.S. Tank). 7. Immerse the pieces in oil, a dewatering type rust preventive at room temperature for 3 minutesto seal the finish and impart corrosion resistance (M.S. Tank).The above parts can be sealed while wet or dry. If parts have to be dried prior to sealing, step 6should be followed with a hot water rinse and the parts to be sealed as soon as they are dry.A wide range of rust preventives are available with us. Consult us on what type of finish andprotection you require for your parts or components and we can suggest a suitable oil.

ALM 81 ALM 81 ALUMINIUM CLEANER Heavy Duty ALM 81 Aluminium Cleaner and Descaler ALM 81 Aluminium Cleaner is a specially formulated highly concentrated ALM 81 Aluminium Cleaner acid for the fast removal of scale and oxide build up from alloy wheels, aluminium vehicle bodies, roller shutter doors and metal casings etc. May also be used for phosphating steel parts prior to painting. A concentrated chemical blend for cleaning all types of aluminium including commercial vehicle bodywork, especially fridge and bulk trailer bodies. It is a concentrated blend of chemical. It works brilliantly at restoring tarnished aluminium that is found on many commercial vehicles such as tipper bodies, aluminium fuel tanks etc. Also helps to protect it against damage from salt and traffic film. ALM81 ALUMINIUM CLEANER we are dedicatedly involved in providing an excellent quality array of aluminium cleaner, for catering the various needs of our customers. his is a fluoride base aluminium cleaner for industrial use.this is a dip application product.this is a single tank application for pretreatment of aluminium before powder coating.we have formulated this product with surfactants, wetting agents, fluoride & solvents to remove light oil, dirt & oxide layer present on components in single dip.this chemical works efficiently at room temp.proper etching/cleaning is achieved in 2-3 minutes time.water wash components after application then air dry. Features: Precisely processed Highly effective Free from impurities

Bio Degradable Degreasing is an alkaline liquid chemical consisting of surfactants, dispersants and corrosion inhibitors. Bio Degradable Degreasing is a multipurpose cleaning agent, Bio Degradable Degreasing widely used for removal of soils, oils, cutting fluids, stamping, buffing and drawing compounds from ferrous as well as non-ferrous metal surfaces. Bio Degradable Degreasing is easily soluble in water at all proportions and is very safe to use as Bio Degradable Degreasing does not contain any chlorinated solvents, phenols, chromates, nitrites or cresols. Bio Degradable Degreasing is non-toxic. Bio Degradable Degreasing can be used by wipe, immersion or spray in various types of cleaning equipments such as tumblers, vibrators, agitators, power washers, steam cleaners, immersion or agitated tanks, ultrasonic or vapour cleaners etc. Since Bio Degradable Degreasing contains corrosion inhibitors, no rinse is required after cleaning hence Bio Degradable Degreasing cleans and protects simultaneously. Bio Degradable Degreasing Protection period may depend on operating parameters and indoor conditions.

3 IN 1 RUST REMOVER CHEMICAL Relying over our expertise in this domain, we are engaged in offering 3 In 1 Rust Remover Chemical to our respected clients. These chemicals are used in only before powder coating for rust removing, light rust removing & metal coating for foundation of powder coating. Use of It increases life of powder coated product Features:- Balanced composition Free from impurity Stable physical and chemical properties low Viscosity Hygienically packed Effectiveness Scale and rust remover concentrate. CRC Rust Remover is a phosphoric acid based concentrate used to remove rust and to clean metal surfaces. It cleans tarnish, oxidation, stains, fingerprints and scale from iron, steel, copper, brass and aluminium.

ALM 81 ALM 81 ALUMINIUM CLEANER Heavy Duty ALM 81 Aluminium Cleaner and Descaler ALM 81 Aluminium Cleaner is a specially formulated highly concentrated ALM 81 Aluminium Cleaner acid for the fast removal of scale and oxide build up from alloy wheels, aluminium vehicle bodies, roller shutter doors and metal casings etc. May also be used for phosphating steel parts prior to painting. A concentrated chemical blend for cleaning all types of aluminium including commercial vehicle bodywork, especially fridge and bulk trailer bodies. It is a concentrated blend of chemical. It works brilliantly at restoring tarnished aluminium that is found on many commercial vehicles such as tipper bodies, aluminium fuel tanks etc. Also helps to protect it against damage from salt and traffic film. ALM81 ALUMINIUM CLEANER we are dedicatedly involved in providing an excellent quality array of aluminium cleaner, for catering the various needs of our customers. his is a fluoride base aluminium cleaner for industrial use.this is a dip application product.this is a single tank application for pretreatment of aluminium before powder coating.we have formulated this product with surfactants, wetting agents, fluoride & solvents to remove light oil, dirt & oxide layer present on components in single dip.this chemical works efficiently at room temp.proper etching/cleaning is achieved in 2-3 minutes time.water wash components after application then air dry. Features: Precisely processed Highly effective Free from impurities