Bio Degradable Degreasing is an alkaline liquid chemical consisting of surfactants, dispersants and corrosion inhibitors. Bio Degradable Degreasing is a multipurpose cleaning agent, Bio Degradable Degreasing widely used for removal of soils, oils, cutting fluids, stamping, buffing and drawing compounds from ferrous as well as non-ferrous metal surfaces. Bio Degradable Degreasing is easily soluble in water at all proportions and is very safe to use as Bio Degradable Degreasing does not contain any chlorinated solvents, phenols, chromates, nitrites or cresols. Bio Degradable Degreasing is non-toxic. Bio Degradable Degreasing can be used by wipe, immersion or spray in various types of cleaning equipments such as tumblers, vibrators, agitators, power washers, steam cleaners, immersion or agitated tanks, ultrasonic or vapour cleaners etc. Since Bio Degradable Degreasing contains corrosion inhibitors, no rinse is required after cleaning hence Bio Degradable Degreasing cleans and protects simultaneously. Bio Degradable Degreasing Protection period may depend on operating parameters and indoor conditions.

VCHEMKLIN is designed to simplify pre-paint treatment of metal aircraft surfaces like wing sections, fuselages as well as automobiles and tractor assemblies. Complete assembled planes can be cleaned and conditioned right on the field without the use of special equipment. Easy hand application of VCHEMKLIN by brushing, swabbing or spraying provides thoroughly clean passivated surface ready for touch-up or complete refinishing. FAST, LOW COST METHOD :- Passivating with VCHEMKLIN is not intended to replace anodizing and chromatising in aircraft and automobile manufacturing. However it produces similar results faster and at much lower cost where those processes are impractical or unavailable. REMOVES, PREVENTS CORROSION :- Light oxides and surface corrosive residues are quickly and easily removed by merely applying VCHEMKLIN by wipe method and rinsing with water. Surfaces is made chemically inert oxide and soil free to prevent corrosion from spreading under paint coatings.

VCCLEAN-HD18 is an universal cleaning composition which could be used be very safely on any metal or assemblies. It can be used for general cleaning for removal of oils, soils, fabricating fluids, burrs, buffing and drawing compounds etc. It is extremely safe to handle and contains no toxic or hazardous constituents and is neither inflammable nor poisonous. It is a solvent based neutral cleaner which can be readily mixed with water in all proportions. VCCLEAN-HD18 can be used by wipe, or immersion in various types of equipments such as ultrasonics, tumblers, agitated tanks. No rinse is mandatory after cleaning with VCCLEAN-HD18 and hence it cleans and protects simultaneously. It can be used as a spray cleaner in service stations and maintenance depots at very low concentrations very effectively, but should not be used in spray washing machines. This composition is bio-degradable and environment friendly.

Blackening Equipment For Metal is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature. VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energy saving, fast, dependable and convenient. It increases productivity and lowers labour costs. Finishing can be done anywhere without special equipment, ventilation, heating systems or any complicated control procedures. EQUIPMENT REQUIRED Acid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used with VCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks and racks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used for degreasing, rinsing & sealant tanks. DIRECTIONS FOR USE 1. Thoroughly clean and degrease the pieces to be blackened in KLN 18. The type and degree of surface soil will determine the length of time and the number of cleaning steps and cleaning temperature (M.S. Tank). 2. Rinse thoroughly in overflowing cold water (M.S. Tank). 3. Surface rust, if present, should be removed following cleaning cycle using RLN 27 at a concentration of 1:1 at room temperature (FRP Tank). 4. Rinse thoroughly in overflowing cold water (M.S. Tank). 5. Immerse the pieces in VCBLK HB-18 solution. VCBLK HB-18 solution is to be diluted with 6 to 12 parts of water depending on alloy and surface, hardness. The immersion time necessary to produce the desired depth of black, is usually one to three minutes. For most parts a dilution of one part VCBLK HB-18 with 9 parts of water would give good results (FRP Tank). 6. Rinse the pieces in overflowing cold water for 30 seconds (M.S. Tank).

Blackening Equipment For Metal is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature. VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energy saving, fast, dependable and convenient. It increases productivity and lowers labour costs. Finishing can be done anywhere without special equipment, ventilation, heating systems or any complicated control procedures. EQUIPMENT REQUIRED Acid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used with VCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks and racks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used for degreasing, rinsing & sealant tanks. DIRECTIONS FOR USE 1. Thoroughly clean and degrease the pieces to be blackened in KLN 18. The type and degree of surface soil will determine the length of time and the number of cleaning steps and cleaning temperature (M.S. Tank). 2. Rinse thoroughly in overflowing cold water (M.S. Tank). 3. Surface rust, if present, should be removed following cleaning cycle using RLN 27 at a concentration of 1:1 at room temperature (FRP Tank). 4. Rinse thoroughly in overflowing cold water (M.S. Tank). 5. Immerse the pieces in VCBLK HB-18 solution. VCBLK HB-18 solution is to be diluted with 6 to 12 parts of water depending on alloy and surface, hardness. The immersion time necessary to produce the desired depth of black, is usually one to three minutes. For most parts a dilution of one part VCBLK HB-18 with 9 parts of water would give good results (FRP Tank). 6. Rinse the pieces in overflowing cold water for 30 seconds (M.S. Tank).

Blackening Equipment For Metal is a new revolutionary development in cold black finishing. It will impart jet black conversion coating to steels, cast iron and other ferrous metals at room-temperature. VCBLK HB-18 process is easy to do in-house. It is non-caustic, non-splattering, safe, energy saving, fast, dependable and convenient. It increases productivity and lowers labour costs. Finishing can be done anywhere without special equipment, ventilation, heating systems or any complicated control procedures. EQUIPMENT REQUIRED Acid Resistant tanks, containers, tumbling barrels, baskets, hooks and racks must be used with VCBLK HB-18 and derusting tank. Plastic or Rubber lined tanks and plastic-coated hooks and racks are suitable for both VCBLK HB-18 and derusting tanks. Mild steel may be used for degreasing, rinsing & sealant tanks. DIRECTIONS FOR USE 1. Thoroughly clean and degrease the pieces to be blackened in KLN 18. The type and degree of surface soil will determine the length of time and the number of cleaning steps and cleaning temperature (M.S. Tank). 2. Rinse thoroughly in overflowing cold water (M.S. Tank). 3. Surface rust, if present, should be removed following cleaning cycle using RLN 27 at a concentration of 1:1 at room temperature (FRP Tank). 4. Rinse thoroughly in overflowing cold water (M.S. Tank). 5. Immerse the pieces in VCBLK HB-18 solution. VCBLK HB-18 solution is to be diluted with 6 to 12 parts of water depending on alloy and surface, hardness. The immersion time necessary to produce the desired depth of black, is usually one to three minutes. For most parts a dilution of one part VCBLK HB-18 with 9 parts of water would give good results (FRP Tank). 6. Rinse the pieces in overflowing cold water for 30 seconds (M.S. Tank).

Vitarag Chemicals is a leading manufacturer of metal Pre Treatment Chemicals which can also be known as powder coating chemicals manufacturer. We have been manufacturing and supplying pre treatment chemicals to Powder Coating Chemicals For Equipment Manufacturers in India and out of India.

1. ZNP-54 ZINC PHOSPHATING CHEMICAL 2. Generally zinc phosphate conversion coating is used to provide long lasting corrosion protection. Almost all automotive industries use this type of conversion coating. It is suitable for the products come against hard weather conditions. Coating quality is better than iron phosphate coating. It forms 2 - 5 gr/m² coating on the metal surface when used as under paint. Application, set up and control of this process are more difficult than other methods and can be applied by immersion or spray. 3. Organic compounds like nickel and manganese are added to the bath to increase the coating performance. Also activation can be used to form small phosphate crystals on the metal surface before zinc phosphating. 4. Zinc phosphate reaction happens in amorphous shape with gray - black color. 5. pH optimizers are added to accelerate the reaction. Temperature, application time, concentration, pH, total acid and free acid values are the parameters which must be under control. 6. Zinc phosphates, coating range between 7 - 15 gr/m², are used in wire drawing, tube drawing and cold forming industries. Phosphated metal workpieces are prepared to the next stage by application of protective lubricans and soap

DESCRIPTION : VCCLEAN-550 is a very effective deburring compound. It can also be used for cleaning, degreasing, derusting, descaling etc. when used in tumblers, vibrators, agitators and deburring equipments. It will remove all loose deposits producing a very smooth and even surface on the components. It can very safely be used for ferrous as well as non-ferrous metals. It is non-toxic and very safe to handle. USES : 1. For deburring ferrous & non-ferrous components. 2. For removal of rust & scales from components when used in tumblers & vibrators etc. alongwith some suitable media APPLICATION :- 1. Add 5-10% of VCCLEAN-550 based on the water added to the tank of the vibrator/tumbler etc. 2. Operate the equipment for a time ranging from ½ hr – 6 hrs depending on the type of operation. Regular addition of chemical may have ro be made for long duration of operation 3. Rinse tumble the components with fresh water. 4. Dip them in a suitable rust preventive like RUST PREVENTIVE OIL depending on the desired period of protection.